HPE Ezmeral Data Fabric Database Binary DiffTablesWithCrc

This utility uses a cyclic redundancy check to detect differences between sets of rows in the specified HPE Ezmeral Data Fabric Database binary tables. Then, for each set of non-identical rows, it performs a detailed comparison. Finally, it generates one or more directories of sequence files. You can use these files either to make a HPE Ezmeral Data Fabric Database binary table identical to its master or merge the rows from two HPE Ezmeral Data Fabric Database binary tables.

Sequence files are binary flat files. You can learn more about them here. To convert a sequence file into a format that you can read, use the HPE Ezmeral Data Fabric Database Binary FormatResult utility.

This utility requires less network bandwidth than the DiffTables utility because it performs a detailed table comparison only on the sets of rows where the CRC algorithm detected a difference. Therefore, consider using this utility when the tables you compare are very similar and you are concerned about the data transfer rate.

Requirements

  • When the cluster runs YARN, it must also use zero configuration failover for the ResourceManager.

By default, the utility considers both the source table and the destination table to be a master table. Therefore, it generates two directories with sequence files. These sequence files contain the puts required to update each table so that it can contain a superset of the rows defined in both tables at the time at which the utility was run.

When you specify a master table, the mapr difftableswithcrc utility generates one of the following output directories:

  • opsForDst. A directory containing sequence files that correspond to each put and delete required to make the destination table identical to the source table.
  • opsForSrc. A directory containing sequence files that correspond to each put and delete required to make the source table identical to the destination table.

A user with write permissions on a table can run the hbase org.apache.hadoop.hbase.mapreduce.Import command to implement the puts and deletes specified in the sequence files.

Required Permissions

The user that runs the mapr difftableswithcrc utility must have the following permissions:

  • The permission readAce on the volumes where the tables are located.
  • The permission for column reads (readperm) on each table.

For information about how to set permissions on volumes, see Setting Whole Volume ACEs.

For information about how to set permissions on tables, see Enabling Table and Stream Authorizations with ACEs.

NOTE
The mapr user is not treated as a superuser. HPE Ezmeral Data Fabric Database does not allow the mapr user to run this utility unless that user is given the relevant permission or permissions with access-control expressions.

Syntax

hbase com.mapr.fs.hbase.tools.mapreduce.DiffTablesWithCrc
-src <source table path>
-dst <destination table path>
-outdir <output directory> 
[-master src|dst ] The master table to use for the diff.
[-first_exit] Exit when first difference is found. 
[-cf <comma separated list of column families>] 
[-starttime <start diff at timestamp>]
[-endtime <end diff at timestamp>] 
[-maxVersions <max number of versions to copy>] 
[-cmpmeta <true|false> (default: true)] 

Parameters

Parameter Description
src

The path to the source table.

  • For a path on the local cluster, start the path at the volume mount point. For example, for a table named testsrc under a volume with a mount point at /volume1, specify the following path:/volume1/testsrc
  • For a path on a remote cluster, you must also specify the cluster name in the path. For example, for a table named customersrc under volume1 in the sanfrancisco cluster, specify the following path:/mapr/sanfrancisco/volume1/customersrc
dst

The path to the destination table.

  • For a table on the local cluster, start the path at the volume mount point. For example, for a table named testdst under a volume with a mount point at /volume1, specify the following path: /volume1/testdst
  • For a table on a remote cluster, you must also specify the cluster name in the path. For example, for a table named customerdst under volume1 in the sanfrancisco cluster, specify the following path:/mapr/sanfrancisco/volume1/customerdst
master

The table that is considered to be the master table. The values are src (the source table) and dst (the destination table). By default, both the source table and the destination table are considered to be the master.

first_exit

By default, the utility compares all the table cells in the specified tables. Set this parameter if you want to exit after the first difference is identified between the tables.

outdir The path to a directory for the sequence files. The utility will create the specified directory. If the specified directory already exists, the command will fail.
cf By default, the utility compares all columns from the master table. If you do not want to compare all columns in the table, you can specify specific columns to include in the comparison. Provide a comma-separated list of column families or columns from a certain column family (column family:qualifier). For example, use the following syntax to include the column family purchases and the column stars in the reviews column family: -columns purchases,reviews:stars
starttime By default, the utility compares all table values regardless of their associated timestamp. You can specify a timestamp to indicate the table cell version at which to start the comparison. The timestamp is a long integer value that is either user-defined or system-defined (epoch in milliseconds). Values with timestamps lower than the specified timestamp will not be included in the comparison.
endtime By default, the utility compares all table values regardless of their associated timestamp. You can specify a timestamp to indicate the table cell version at which to end the comparison. The timestamp is a long integer value that is either user-defined or system-defined (epoch in milliseconds). Values with timestamps greater than or equal to the specified timestamp will not be included in the comparison.
maxVersions By default, the utility compares all versions from the master table. If you do not want to diff all versions, use this parameter to specify the number of recent versions to include in the comparison.
cmpmeta A Boolean value that specifies whether or not to compare table metadata such as column families and ACEs. The default is to compare metadata (true).

Example

Compares two HPE Ezmeral Data Fabric Database tables:
[user@hostname ~]$ hbase com.mapr.fs.hbase.tools.mapreduce.DiffTablesWithCrc -src /customerTableA -dst /customerTableB -outdir /customerTableCompare
2015-03-04 17:52:40,912 INFO  [main] Configuration.deprecation: hadoop.native.lib is deprecated. Instead, use io.native.lib.available
DiffTablesMeta completed. Metadata of the two tables is same.
....
Mapreduce job completed. The tables mismatch.
NUM_ROWS_MISMATCH_IN_SRC:32; NUM_ROWS_MISMATCH_IN_DST:30. Please check diff in /customerTableCompare